国产综合无码一区二区三区|精品香蕉一区二区三区|91久久久久无码精品国产软件|久久精品2021国产

您好,歡迎光臨思孚科技網站!
螺旋絲錐
專業制造 卓越品質
螺旋絲錐

螺旋絲攻系列
螺旋絲攻對在盲孔內攻牙,切屑連續排出的鋼鐵材質效果良好。因為約35°之右旋蝸槽切屑可從孔內向外排出,切削速度可較直槽絲攻加快30-50%,盲孔 之高速攻牙效果良好因排屑順利。對鑄鐵等切屑成粉末狀的材料效果差。
一般用螺旋絲攻
漲大徑用螺旋絲攻
不銹鋼用螺旋絲攻
深孔用螺旋絲攻
鍍鈦處理螺旋絲攻
氧化處理螺旋絲攻
鋁專用螺旋絲攻

Screw tap series
Screw tap in the blind hole tapping, chip continuous discharge of steel material effect is good. Because about 35 ° of the right hand worm groove chip from the hole introverted effluent out, cutting speed can be a straight flute silk attack speed up 30-50%, blind hole of high speed tapping effect is good for clearance smoothly. For cast iron, and other chip into powder material effect is poor.
General use screw tap
A major diameter screw tap
Stainless steel screw tap
Deep hole with screw tap
Plating titanium processing screw tap
Oxidation treatment screw tap
Aluminum special screw tap

螺紋攻牙鉆孔徑對照表

公制粗螺紋 標準徑 2級牙鉆孔徑
最大 最小
M1.0×0.25 0.75 0.785 0.729
M1.1×0.25 0.85 0.885 0.829
M1.2×0.25 0.95 0.985 0.929
M1.4×0.3 1.10 1.142 1.075
M1.6×0.35 1.25 1.321 1.221
M1.7×0.35 1.35 1.421 1.321
M1.8×0.35 1.45 1.521 1.421
M2.0×0.4 1.60 1.679 1.567
M2.2×0.45 1.75 1.838 1.713
M2.3×0.4 1.90 1.979 1.867
M2.5×0.45 2.10 2.138 2.013
M2.6×0.45 2.20 2.238 2.113
M3.0×0.5 2.50 2.599 2.459
M3.5×0.6 2.90 3.010 2.850
M4.0×0.7 3.30 3.422 3.242
M4.5×0.75 3.80 3.878 3.688
M5.0×0.8 4.20 4.334 4.134
M6.0×1.0 5.00 5.153 4.917
M7.0×1.0 6.00 6.153 5.917
M8.0×1.25 6.80 6.912 6.647
M9.0×1.25 7.80 7.912 7.647
M10×1.5 8.50 8.676 8.376
M11×1.5 9.50 9.676 9.376
M12×1.75 10.30 10.441 10.106
M14×2.0 12.00 12.210 11.835
M16×2.0 14.00 14.210 13.835
M18×2.5 15.50 15.744 15.294
M20×2.5 17.50 17.744 17.294
M22×2.5 19.50 19.744 19.294
M24×3.0 21.00 21.252 20.752
M27×3.0 24.00 24.252 23.752
M30×3.5 26.50 26.771 26.211

絲攻尺寸表

公 制 英 制 英 制 直 徑φ 四角□ PT PS PF 直徑φ 四角□
M3 W1/8 4 3.22 1/8 1/8 1/8 8 6
M4 M4.5 W5/32 5 4 1/4 1/4 1/4 11 9
M5 M5.5 W3/16 5.5 4.5 3/8 3/8 3/8 14 11
M6 U1/4 W1/4 6 4.5 1/2 1/2 1/2 18 14
U5/16 W5/16 6.1 5 5/8 19 15
M8 M7 6.2 5 3/4 3/4 3/4 23 17
M10 M9 U3/8 W3/8 7 5.5 7/8 24 19
M11 U7/16 W7/16 8 6 1 1 1 26 21
M12 8.5 6.5 11/8 11/8 28 21
U1/2 W1/2 9 7 11/4 11/4 11/4 32 26
M14 M15 U9/16 W9/16 10.5 8 13/8 13/8 13/8 35 26
U5/8 W5/8 12 9 11/2 11/2 11/2 38 29
M16 12.5 10
M17 13 10
M18 U3/4 W3/4 14 11
M20 15 12
M22 U7/8 W7/8 17 13
M24 M25 19 15
M27 M26 U1 W1 20 15
M28 21 17
U1-1/8 W1-1/8 22 17
M30 23 17
M32 U1-1/4 W1-1/4 24 19
M33 25 19
M35 M34 U1-3/8 W1-3/8 26 21
M36 M36 28 21
M39 M40 U1-1/2 W1-1/2 30 23
M42 W1-5/8 32 26
M45 U1-3/4 W1-3/4 35 26
M48 W1-7/8 38 29